Senin, 14 Maret 2016
Jumat, 29 Januari 2016
APX CPS R14.00 for APX1000 APX5000
 | |
| Motorola APX1000 |
Supported model : APX8000XE; APX8000; APX7500;APX7000;APX7000XE; APX7000L; APX6500; APX6500Li; APX6000; APX6000XE; APX6000Li; APX5500; APX5000; APX4500; APX4500Li; APX4000; APX4000XH; APX3000; SRX2200; TXM2000; APX2500; APX2000; APX1500;APX1000
New Radio Features Supported:
IMPORTANT NOTE: Firmware version R14.00.00 or higher is required for the following features to work
in the radio:
Support for the new APX 8000 portable All-Band radio (Wi-Fi support)
Support for the new APX 4000XH portable radio
Support for the APX 4000 900 MHz (2 Knob)
Support for the APX 1000 900 MHz (2 knob)
OTAR and GPS support via V.24 in TXM2000
Support for P25 paging / QCII Encoding tone signaling for APX subscribers
APX 6000/7000/XE HAZLOC re-certification (radios updated to the TIA4950 safety standard)
Support for RF Modem functionality on Portable Subscriber Units
Long Press Power Off Support added for APX Control Heads
Added One Button Tones capability for APX Portables, wired and Bluetooth accessories
APX DVRS supported on non MSI systems
DVRS Conventional PTT ID increased from 7 to 8 digits
Motorola ATS2500i terbaru Programming Software
Anda mungkin punya unit motorola ATS2500i tetapi anda tidak bisa memprogramnya
 |
| ATS2500i |
CP Series CPS R02.05 AZ Build63
1. Introduction
Welcome to
the CP Series Customer Programming Software (CPS) for CP1300, CP1600, CP1660,
CP476, CP477, CP350, Walka Talka, CB PRO Plus, CP1200,
CP246, CP1208, CP1308, CP1608 and CP1668 radios.
2. What's new in this release
Version
R02.05 (Build 63)
|
Notes
Support new model AZH03QDH8AD7, which has 138 channels.
|
R02.02 (Build 58)
|
Support Battery Type programmable
button.
|
R02.01 (Build 56)
|
Support some new Korean and
Australian models.
Updated driver installation method.
|
R02.00 (Build 53)
|
Support MDC and Quik-Call II signaling system.
|
R01.07 (Build 46)
|
Support non-display model.
Support for the V3, V4 radios.
|
R01.06 (Build 41)
|
Enhance CP350 radio feature.
|
R01.05 (Build 39)
|
Support CP350 and CB PRO Plus radio.
Support band 350~390MHz radio.
|
R01.04 (Build 35)
|
Support new model AZH03KDH4AA4.
Report feature enhancement.
|
R01.02 (Build 30)
|
Support for the UHF1 radios.
|
R01.01 (Build 28)
|
Support for the VHF radios.
Add Simplified Chinese support.
Add User/Dealer Mode Switch function.
Add DTMF Reset Duration function.
|
R01.00 (Build 21)
|
Support for the UHF2 radios.
Drag and drop support between models.
Support for multiple selection configuration. For example, select
several channels in the tree view and set the parameters to the same value at
once.
Support for custom views and undo/redo.
|
3. Requirements
Operating System
|
Microsoft® Windows® XP
Home/Professional Edition
Microsoft® Windows® Vista
Microsoft®
Windows® 7
Microsoft®
Windows® 8
|
Hardware Recommendations
|
·
The application takes approximately 350 MB of free disk space on your PC. However, more space would be required to save archive files of
your radios. Each archive file varies
in size depending on the features of the radio.
|
·
For processor speed and RAM, the recommendations given by
Microsoft for the release of the operating system that you are using should
be sufficient.
|
·
A USB port.
|
·
A CD-ROM drive.
|
·
For best display results, set the DPI setting of your PC to the Normal
size (96 DPI).
|
4. Installation, Removal
Installation
|
You
need to have Administrator rights on the target PC in order to install the
software.
Follow the steps below for the
CD-ROM version:
·
Insert the CD-ROM containing the installation into the CD-ROM
drive.
·
If the installation application doesn’t start within 30 seconds,
the auto-run feature for CD-ROMs for you operating system is likely
disabled. Browse to your CD-ROM and
run the setup.exe program. For
example, if the E:\ drive is the CD-ROM, run E:\setup.exe.
Follow the steps below for the
software package version:
·
Unzip the CPS package to a directory of a local disk.
·
Browse to this directory and run the setup.exe program.
Note:
1.
During re-install, settings for preferences and dealer
information will be reset to their default values. You will need to check
these settings after the new version has been installed and make changes as
necessary.
2.
If a previous version of CPS has already been installed, you
will be given the option to “Repair” or “Remove”. If you are upgrading the CPS, then remove the previous version
and start the installation process again.
If you are re-installing the CPS, then choose the repair option.
|
Removal
|
From
the Start button on the task bar of your operating system, select Settings
> Control Panel. Select the Add/Remove Programs option within the control
panel. Select the CP Series Customer Programming Software item in the “Currently
installed programs” box and click the remove button.
|
5. Driver installation
Windows XP Operating System
|
Before connect the USB
cable to computer, please make sure your Windows Update setting is “Ask me to
search Windows Update every time I connect a new device” via right click “My
Computer” -> “Properties” -> “Hardware” -> “Windows Update”.
Follow
these steps to install the driver:
1. Connect the USB cable between the host
computer and the radio.
2. Windows will open a “Found New
Hardware Wizard” window.
3. Select “No, not this time” and press
Next.
4. Select “Install the software
automatically (Recommended)” and press Next.
5. Wait while the computer searches and
installs “CP210x USB Composite Device“. If the operating system prompts you
that the software has not passed Windows Logo testing, press Continue Anyway.
6. Windows will open a second “Found New
Hardware Wizard” window.
7. Select “No, not this time” and press
Next.
8. Select “Install the software
automatically (Recommended)” and press Next.
9. Wait while the computer searches and
installs “CP210x USB to UART Bridge Controller”.
|
Windows
Vista Operating System
|
Before connect the USB
cable to computer, please make sure your Windows Update setting is “Ask me
each time I connect a new device before checking for drivers” via right click
“Computer” -> “Properties” -> “Advanced System Settings” -> “Hardware”
-> “Windows Update Driver Settings”.
Follow
these steps to install the driver:
1. Connect the USB cable between the host
computer and the radio.
2. Windows will open a “Found New
Hardware” window.
3. Select “Locate and install driver software (recommended)”.
4. Wait while the computer searches and
installs the driver.
|
Windows 7 Operating System
|
Before connect the USB
cable to computer, please make sure your Windows Update setting is “Install
driver software from Windows Update if it is not found on my computer” via right click “Computer” -> “Properties”
-> “Advanced System Settings” -> “Hardware” -> “Device Installation
Settings”.
To Windows 7 (32 bit) operating system, the driver will be
automatically installed and ready for use when connect the USB cable between
the host computer and the radio.
To Windows 7 (64 bit) operating system, follow these steps
to install the driver:
1.
Connect the USB cable between the host computer and the
radio. The system prompts the driver was installed unsuccessfully.
2.
Run Device Manager via right click My Computer -> System
Properties -> Hardware -> Device Manager.
3.
Select Other Devices then right click “CP2102 USB to UART
Bridge Controller” and run Update Driver Software.
4.
Choose Search automatically for updated driver software.
5.
Wait while the computer searches and updates the driver.
|
6. Legal notice
MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized
M logo are trademarks or registered trademarks of Motorola Trademark Holdings,
LLC and are used under license. All other trademarks are the property of their
respective owners. © 2011-2013 Motorola
Solutions, Inc. All rights reserved.
Microsoft® and Windows® are registered trademarks
of Microsoft Inc.
Jika ingin mencoba silakan sms/call me atau email
Langganan:
Postingan (Atom)